- 您现在的位置：买卖IC网 > Sheet目录341 > MAX6968AAE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-SSOP
8-Port, 5.5V Constant-Current LED Driver
Detailed Description
The MAX6968 LED driver comprises a 4-wire serial
interface driving eight constant-current sinking open-
drain output ports. The outputs drive LEDs in either
static or multiplex applications (Figure 1). The constant-
current outputs are guaranteed for current accuracy
not only with chip-supply voltage variations (5V ±10%
and 3V to 5.5V), but also over a realistic range of driver
output voltage drop (0.5V to 2.5V). The drivers use cur-
rent-sensing feedback circuitry (not simple current mir-
rors) to ensure very small current variations over the full
allowed range of output voltage (see the Typical
Operating Characteristics ).
The 4-wire serial interface comprises an 8-bit shift reg-
ister and an 8-bit transparent latch. The shift register is
written through a clock input CLK and a data input DIN
and the data propagates to a data output DOUT. The
data output allows multiple drivers to be cascaded and
operated together. The contents of the 8-bit shift regis-
ter are loaded into the transparent latch through a latch
enable input LE. The latch is transparent to the shift
register outputs when high, and latches the current
state on the falling edge of LE.
Each driver output is an open-drain constant-current
sink that should be connected to the cathode of either
a single LED or a series string of multiple LEDs. The
LED anode can be connected to a supply voltage of up
to 5.5V, independent of the MAX6968 supply, V+. The
constant-current capability is up to 55mA per output,
set for all eight outputs by an external resistor, R SET .
Initial Power-Up and Operation
An internal reset circuit clears the internal registers of
the MAX6968 on power-up. All outputs OUT0 – OUT7,
therefore, initialize high impedance, and the interface
output DOUT initializes low, regardless of the initial
logic levels of the CLK, DIN, OE , and LE inputs.
4-Wire Serial Interface
The serial interface on the MAX6968 is a 4-wire serial
interface using four inputs (DIN, CLK, LE, OE ) and a
data output (DOUT). This interface is used to write dis-
play data to the MAX6968. The serial-interface data
word length is 8 bits, D0 – D7. See Figure 2.
The functions of the five interface pins are as follows.
DIN is the serial data input, and must be stable when it
is sampled on the rising edge of CLK. Data is shifted in,
MSB first. This means that data bit D7 is clocked in first,
followed by 7 more data bits finishing with the LSB D0.
LE
t CL
t CH
t CP
t LS
t LW
t LF
CLK
t DH
t DS
DIN
D7
D6
D1
D0
t DO
DOUT
OE
t OEL
t OEW
t OEH
D7
80%
.
OUT_
Figure 2. 4-Wire Serial-Interface Timing Diagram
t f
20%
t r
_______________________________________________________________________________________
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX6970AUE+
IC LED DRIVER LINEAR 16-TSSOP
MAX6971AUG+T
IC LED DRIVER LINEAR 24-TSSOP
MAX6974ATL+
IC LED DRIVER LINEAR 40-TQFN
MAX6977AAE+
IC LED DRIVER LINEAR 16-SSOP
MAX6978AUE+
IC LED DVR CONST-CURR 16TSSOP
MAX6979AUG+
IC LED DRIVER LINEAR 24-TSSOP
MAX6983AUG+T
IC LED DRIVER LINEAR 24-TSSOP
MAX71020AEUI+
IC ENERGY METER 1PH 28TSSOP
相关代理商/技术参数
MAX6968AAE+T
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6968AAE-T
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6968AEE
制造商:Maxim Integrated Products 功能描述:8-PORT, 5.5V CONSTANT-CURRENT LED DRIVER - Rail/Tube
MAX6968AEE+
制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX6968APE
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6968APE+
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6968AUE
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6968AUE+
功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube